SVGA 270LCD ProjectorUser Guide
1-9OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHBasic OperationBasic manipulation to show in the table 1-2 can be done easily by the control pan
1-10OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Table 1.2 Basic Operation (continued)Item DescriptionVOLUMEVolume adjustment : Reduce VOLUME ↔ Increas
1-11OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHSetup MenuThe following adjustments and settings arepossible when SETUP is selected at the top
1-12OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Input MenuThe following functions are available when INPUT is selected on themenu. Select an item with
1-13OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHImage MenuThe following adjustments and settings are available when IMAGE isselected on the men
1-14OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Options MenuThe following adjustments and settings are available when OPTIONS isselected on the menu.
1-15OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHNo Signal MenuThe same adjustments and settings are available as with the Image andOptions menu
* For disposal of used lamp, treat according to the instruction of community authorities.* Since the lamp is made of glass, do not apply shock to it a
1-17MMAAIINNTTEENNAANNCCEE ((ccoonnttiinnuueedd))ENGLISHReplacing the Lamp1. Switch the projector OFF, remove the power cord from the poweroutlet, an
1-18MMAAIINNTTEENNAANNCCEE ((ccoonnttiinnuueedd))Air Filter MaintenanceThe air filter should be cleaned as described below at intervals of approximat
ENGLISHLiquid Crystal ProjectorSVGA 270 USER'S MANUAL1-1Thank you for purchasing this HITACHI liquid crystal projector.Please read the accompanyi
1-19ENGLISHTROUBLESHOOTINGOSD MessageA message like the bottom table sometimes displays it with this opportunity at the time of powersource on.Cope in
1-20TTRROOUUBBLLEESSHHOOOOTTIINNGG ((ccoonnttiinnuueedd))Indicators MessageThe POWER indicator, LAMP indicator and TEMP indicator light or blink in t
1-21ENGLISHTTRROOUUBBLLEESSHHOOOOTTIINNGG ((ccoonnttiinnuueedd))SymptomBefore requesting repair, check in accordance with the following chart. If the
1-22SPECIFICATIONSItem SpecificationProduct name Liquid crystal projectorModel CP-S220WLiquidcrystalpanelPanel size 1.8 cm (0.7 type)Drive system TFT
1-23ENGLISHSSPPEECCIIFFCI ICAATTIIOONNSS ((ccoonnttiinnuueedd))Dimension Diagram2897645.674.5210WARRANTY AND AFTER-SERVICE* When a problem occurs,
1-24REGULATORY NOTICESWARNING: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of
9-1TECHNICALTECHNICALExample of computer signalResolution H× VfH (kHz) fV (Hz) Rating Signal modeDisplaymodeNote 1640 × 35037.9 85.1 VESA VGA-1 Zoom i
9-2TTEECCHHNNIICCAALL((ccoonnttiinnuueedd))Initial set signalsThe following signals are used for the initial settings.The signal timing of some comput
1-2FEATURESThis liquid crystal projector is used to project various computer signals as well as NTSC / PAL /SECAM video signals onto a screen. Little
1-3BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))ENGLISHPart NamesPower SwitchAC Inlet(to the Power Cord)Ventilation Openings(Intake)ZOOM knobFOCUS ring
1-4BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))Part Names (continued)VIDEOSTANDBY/ONPOSITIONFREEZEMAGNIFYVOLUMEAUTOOFFTIMER BLANKMENUSELECTRGBMUTEMENU
1-5INSTALLATIONInstallation of the Projector and ScreenInstall the projector in a suitable environment according to instructions of theaccompanying ma
1-6IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))RGB Signal Input:Connect the RGB IN terminal of the projector to the display signal output of the c
1-7IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))ENGLISHExample of system setupAC InputVideo tape recorder with S jackVideo tape recorderComputer(de
1-8OPERATIONSPower On/OffPower On1. Confirm that power cord is connected properly.2. Push "I" of the power switch. Standby mode is set up an
Commentaires sur ces manuels